Factory Five Racing Forum banner
1 - 12 of 12 Posts

·
Senior Charter Member
Joined
·
559 Posts
Discussion Starter · #1 ·
Anyone have a Part# or phone # so I can order this Manual?

Thanks in Advance.
 

·
Premium Member
Joined
·
3,886 Posts
Ford Fuel Injection & Electronic Engine Control : All Ford/Lincoln-Mercury Cars and Light Trucks 1988 to 1993
by Charles O. Probst
Ford FRPP part # is M-1832-Z1, for $29.95

But you can get it from www.amazon.com for $20.97

Does this mean you're coming back from "the dark side"? (I see a Holley potato in your sig) :D

Forrest
 

·
Senior Charter Member
Joined
·
559 Posts
Discussion Starter · #3 ·
Thanks Forrest.

A Little Clearification.

The part# Info I'm Looking for is for the Ford Motorsports EFI Engine Management Manual.

Cost $5.00 and tells you how to splice the factory engine, sensor and computer harness into a Painless harness.

Note: I already have the Helm, Electrical & Vacuum Trouble shooting Manual for my wiring diagrams for the Donor disassembly.
 

·
Premium Member
Joined
·
3,886 Posts
Oh.
Sorry, never heard of that. It's not in the FRPP catalog, but you probably already know that.

Sounds useful...when you find it, please post it.

Forrest
 

·
Senior Member
Joined
·
6,546 Posts
According to the FRPP 2002 Catalog you can get just the manual this way:

Send $5.00 to:

Ford Motor Company
P.O. Box 51394
Livonia, Michigan 48151

You could probably also call FRPP and order it from them.

Ozona
 

·
Senior Charter Member
Joined
·
559 Posts
Discussion Starter · #6 ·
Thanks Ozona,

I'll give FRPP a shout in the AM to see If I can order over the manual over the phone, rather than snailmail.
 

·
FFCobra Craftsman
Joined
·
1,333 Posts
Capt. Al -

Are you looking for the "Multiport EFI Engine Management Harness" book? If so, it's part # ISM-12071-C302, cost $5, call the FMS Tech Hot Line at 810-468-1356.

If you are integrating the painless car harness with the Ford engine and computer harness, this 'book' (it's only 25 pages) is essential. It comes w/ the new FMS computer harness kit.
 

·
Senior Charter Member
Joined
·
559 Posts
Discussion Starter · #8 ·
Barry,

Yes, That's the manual that you had suggested I purchase since I also went with the Carb Kit .

I 'll order the Manual in the A.M.

Thanks again for the Info.

Capt Al
 

·
Senior Member
Joined
·
6,546 Posts
Not trying to be a smart ass, but aren't you building a carb car? You won't need this with a carb, just with the FRPP wiring harness (same as a 93 5.0)

Regards,

Bill
 

·
Registered
Joined
·
3,471 Posts
I picked up a used copy of the book Forrest spoke of on Amazon for $13.
At some point I'll be switching to mass air and I figured it may come in handy.
RR
 

·
Senior Charter Member
Joined
·
559 Posts
Discussion Starter · #11 ·
Ozona,

You are 100% Right.

This manual isn't required for the Carb kit build.

Its only a $5.00 Electrical Manual that I'd like to add to my FFR research collection.

I just think its a smart play to have all bases covered.
 

·
Senior Member
Joined
·
6,546 Posts
OK..just checkin, figured you might have been sniffin' POR-15 or something. ;)

:D
 
1 - 12 of 12 Posts
Top