Search Results for ‘wiring’

Hello experts! I'm hoping someone might be able to point me to the next area to start investigating... I bought a MK1 2 years ago (fox body donor w/302 EFI) and at the time, turn signals and driver's side lo-beam were not working (lo-beam was only receiving 6 volts). No big deal as I didn't...

I have a MK1 built (not by me) in 1999... having electrical issues, which I will post in proper forum.

I'm using a FAST 2.0 EZ EFI system on my car. The computer wants to control(adjustable via keypad) the fan. I have the sensor installed into the manifold by the water neck and that sensor plug goes back into the main EFI harness. I have a blue wire labeled "Fan1 Relay" with a 1 amp inline fuse...

Hey guys, not an electrical genius by any means but I do alright. On wiring up my Fast EFI 2.0 system along with the Fast distributor/controller/coil. Instructions tell me to wire a couple of components into a switched 12 volt wire that is hot during run AND cranking. Where do I find that. I am...

hey, I have a question i am hoping somebody can help me with. I'm currently building a MK4 with a 4.6 DOHC from a 1996 Mustang Cobra. i am using a Ron Francis chassis harness, and the ford engine harness. has anybody done this before, and if so do the know which pins on the ECM do i need to...

I have the complete kit pull out headlight switch. When I pull it out the parking lights and the gauges lights come on but I dont get any power to the low beams. Are we suppose to still use a separate switch for the low and high beams? I'm thinking about wiring the Blue HDLT SW DIM SW wire...

Hi Guys, We have had a significant amount of interest from the forum to do another group buy in tandem with the guys at Pro-Touring and Lateral-G. There was another post about this earlier this week but there was some confusion about the post. I've spoken with Ray, one of the moderators and...

Hi Guys, We have had a significant amount of interest from the forum to do another group buy in tandem with the guys at Pro-Touring and Lateral-G. There was another post about this earlier this week but there was some confusion about the post. I've spoken with Ray, one of the moderators and...

Hi Guys, We have had a significant amount of interest from the forum to do another group buy in tandem with the guys at Pro-Touring and Lateral-G. There was another post about this earlier this week but there was some confusion about the post. I've spoken with Ray, one of the moderators and...

I have the Ron Frances complete wiring harness and the gauge set is supposed to "snap" in. The connections are completely wrong. I have the "vintage style" gauge set rather than the modern set. Does Ron Frances make 2 different types of harness for the different gauge set or am I going to...

So I have started wiring up my car with the donor harness and there is a bunch of extra wiring that I would like to remove sooner rather then later. However using the wiring diagrams found in my Haynes manual isn't exactly instilling much confidence in me as to what is ok to remove and what has...

I'm in the process of wiring the dash and am having some problems with oil pressure and water temp gauges. I'm using the FFR electric classic gauges with the supplied sending units. First with the water temp. From the gauge, there are 2 wires that go to the sending unit. When Ii heat the...

I'm doing the mock up wiring of my headlights and turn signals and have read numerous post recommending separating the wiring into individual weather pak fittings to facilitate removing the body without cutting the wiring. Am I missing something or has the RF Wire harness been modified? I have...

is it going to be a problem if i cut to shorten the length of the wires for the abs sensors? or if i was to loop the wires so compensate the slack will it make any interferiance noise? thank you very much.

:confused1:hello everyone im stuck on the fuel tank plumbing and wiring.....i know the threads ive searched say this topic has been beaten to death however i never find the solution. i have 2003-04 fuel tanks and a 2006 ls7 ecu. im running the painless fuse box. any links or help on this...

Thank you everyone for your thoughts and comments. The biggest shock to me is that FFR for all practical purposes has abandoned the original 'donor concept' in favor of suppling eveything new in their 'complete kit' package (whose appeal I can understand). Guess I've been busy keeping my head...

I would like to open a discussion about current ideas/approaches to wiring a FFR kit car that appeal to builders. While I have continued to provide and refine professionally dieted OEM harnesses in conjuction with a quality aftermarket chassis harness (a system developed orignally by Roger...

Gentlemen, I would like to take the time to share my experience with one of our vendors. The company is WIREDIET.com. Art Cuesta did a super job dieting my harness from an 89 Mustang. Car started on the first try and ran perfectly. It was a huge relief since I had "butchered" it by attempting...

Has anyone embarked on wiring the car manually? Just buying a fuse block and spools of wire? I'm looking for an estimate of how much wire I'll need and some recommendations on wire gauges. I'm an electrical engineer, so I can do the math... just seeing what has worked well in the past...