FFCars.com : Factory Five Racing Discussion Forum - Reply to Topic
Thread: upper control arms Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 
 
 

Register Now



In order to be able to post messages on the FFCars.com : Factory Five Racing Discussion Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
09-24-2019 02:39 PM
Dave M John, might be a good idea but I'm still running with the original Fox LCA's. Never saw the need to spend the $ on replacement as these have worked perfectly up till now.
09-24-2019 12:41 PM
phileas_fogg Maybe too late, but have you considered replacing the LCA bushings with the spherical bearing inserts from F5 (http://www.factoryfiveparts.com/1633...-control-arms/)? Lots of good things said about the improvement to the suspension, plus one less set of bearings to grease at PM time.


John
09-23-2019 08:13 PM
Dave M Ok, so I pulled the the cross shafts and pivots off. They were not the source of the noise. Cleaned them up, ground some small channels into the shafts with the Dremel and now grease comes out both ends of the pivits. I could see a very slight ware pattern on parts of the shafts which I think had allowed some grease to get in so they were all moving freely. I'm still not positive where the noise was coming from but think it might be the LCA's. The bushings look like they had allowed the arm to move forward slightly from where it should sit. This was allowing the front bottom corner under the bushing to come in contact with the front most bracket weld on both sides. Took the lowers off and ordered some new bushings, we'll see how it sits when its back together. As long as everything is apart it'll be a good time to clean and relube wheel bearings and the shock pivits.
Hopefully the parts won't take to long getting here as some of the years best driving weather is here. Love the fall in New England.
09-21-2019 09:45 PM
CraigS I agree, if yours will still move, you may be able to salvage them. OTOH, you may be able to buy just new cross shafts and pivots if they will fit the rest of your UCA. I did that and it worked fine. I bought the 5" cross shaft and 92025 pivots. They have grooves in the ID of the dlerin and it is really nice to see 6 little squirts of grease come out of each side of the pivot. There have been several permutations of arms used by FFR so I can't be sure all will fit but one key is the thread diameter of the sleeves. These parts are all 3/4x16.
Go here;
https://www.spcalignment.com/images/...t_2018-web.pdf
to page 150. Once you have the numbers, I usually order through Summit. Depending how many parts you need it is sometimes less expensive to buy a complete arm.
09-21-2019 08:19 PM
weendoggy If you have the "original" SPC UCA's, they are different than the new ones. New ones have a delrin bushing and are also shorter in length. Plus, they will need new arms, etc. in order to work correctly because of the shortened shaft. Best would be to buy new ones complete if needed. No, you can't order new parts for the old style, they're not made anymore.

My suggestion is to take the old one apart and make sure it's not galled to the point of replacement, clean it up, open up your grease hole (sounds bad) and put it back together and run it. I've done mine once in 18yrs and no issues. Next thing is to remember to grease them often enough so you see the grease extrude from the joint.

Now, if you already have the delrin style bushings, you can disregard most of my post. Those you can get parts for.
09-21-2019 06:27 PM
Dave M
upper control arms

I have a MKIII with the older version front UCA's that are known to not take grease all that well. Noticed a slight noise lately when I leaned on the fender, so am thinking I have a dry bushing. My thought is to pull them apart and clean and maybe cut some additional grease channels in the cross shafts. Just wondering what the newer versions look like. Do they have channels in the shafts or the bushings? If in the shafts if somebody might have a pic or a good description of what they look like.
TIA Dave

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome

 

Welcome to FFCars! The representations expressed are the representations and opinions of the FFCars.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Factory Five Racing, Inc. or Ford Motor Company. This website has been planned and developed by FFCars.com and its forum members and should not be construed as being endorsed by Factory Five Racing, Inc. or Ford Motor Company for any purpose. "FFR", "Factory Five", "Factory Five Racing", and the Factory Five Racing logo are registered trademarks of Factory Five Racing, Inc. FFCars.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting the FFCars.com Forum dedicated to Factory Five.