|
Junior Member
Join Date: Jan 2011
Location: Los Angeles/California
Posts: 10
|
UNFINISHED MK IV COMPLETE KIT WITH NEW ENGINE FACTORY 351w & TRANNY PKG -- CALIFORNIA
UNFINISHED MK IV COMPLETE KIT WITH NEW ENGINE FACTORY 351w AND TRANNY PACKAGE -- CALIFORNIA
POWDER COATING ROADSTER CHASSIS
FFR ELECTRIC GAUGES
GAUGES, KIRKHAM, ELECTRIC, 7 PIECE KIT
351 HEADERS-ROADSTER
302-351 ENGINE/TRANS MOUNTS
31 SPLINE 10.625" DRIVESHAFT
DRIVESHAFT, 3" CHROMOLY TUBE, 31 SPLINE,
302/351 w/TKO, 10.625", BLACK, W/(4) M12-1.5 x
25MM BOLT
BODY CUT-OUTS
VINTAGE RACE SEATS
BOX 12 K 3-LINK DELUXE REAR SUSPENSION
87-93 17" 5 LUG HALIBRAND REPLICA WHEELS
87-93 REAR AXLE, mk3
2 @ WHEEL, ALUMINUM, 1 PIECE, 17"x 9", 5 LUG,
HALIBRAND STYLE, 5 SPOKE, ANTHRICITE, 6" B.S.
(24MM OFFSET), WITH SPINNER AND LUG NUTS
2 @ WHEEL, ALUMINUM, 1 PIECE, 17"x 10.5", 5 LUG,
HALIBRAND STYLE, 5 SPOKE, ANTHRICITE, 6.7" B.S.
(27MM OFFSET), WITH SPINNER AND LUG NUTS
BUMPER KIT
STAINLESS 4/4 SIDE EXH. w/HARDWARE
SIDE EXHAUST, 4 INTO 4 STAINLESS STEEL,
POLISHED, SET with kit
WIND WINGS
SUN VISORS
ROADSTER HEATER/DEFROSTER
MK IV LOGO FLOORMATS
MK IV LH CHROME ROLL BAR
MK IV RH CHROME ROLL BAR
PERFORMANCE 11.65" REAR BRAKE SET
REAR AXLE HOUSING W/ 3-LINK, 5 LUG A
AXLE, HOUSING, 8.8, 59.25" FLANGE TO FLANGE,
3.31 GEARS, TRACTION LOK, 31 SPLINE C-CLIP
AXLES, 5 LUG 1/2"-20 x 1.75" STUDS, 3-LINK MOUNT,
FOX PINION FLANGE, BARE
ENGINE FACTORY 351w 400 HP HIGH OUTPUT COBRA REPLICA ENGINE AND TRANNY PACKAGE
PRECISION MACHINED 351W ROLLER BLOCK
NODULAR CAST IRON CRANKSHAFT
SHOT PEENED & STRESS RELIEVED CONNECTING RODS WITH ARP RETAINING BOLTS
Hypereutectic Federal Mogul 9.7 TO 1 COMPRESSION W/ Duralube Coating
SPEED PRO Chrome Moly PISTON RINGS
3 PIECE STEEL ROLLER STYLE TIMING CHAIN
Steel Roller Xtreme Energy CAMSHAFT DELIVERS MID-RANGE HORSE POWER AND Great LOW END TORQUE
NEW MELLING OIL PUMP AND SCREEN
EDELBROCK RPM ALUMINUM HEADS 60cc COMBUSTION CHAMBER with Bronze Guides
STAINLESS STEEL SWIRL POLISHED INTAKE VALVES
STAINLESS STEEL SWIRL POLISHED EXHAUST VALVES
COMP CAMS ULTRA PRO MAGNUM CHROME MOLY STEEL ROLLER ROCKERS
HARD SEATS FOR UNLEADED OR REGULAR FUEL
HEAVY DUTY 1.45 DIAMETER VALVE SPRINGS, 7 DEGREE LOCKS
NEW HEAVY DUTY CHROME MOLY PUSH RODS
NEW REAR SUMP 5 QUART OIL PAN
TIMING CHAIN COVER WITH SCALE
COBRA BLACK WRINKLED ALUMINUM VALVE COVERS
STEEL BILLET 157 TOOTH STANDARD FLYWHEEL (FOR 5 SPEED TRANSMISSIONS)
NEW EDELBROCK PERFORMER RPM DUAL PLANE INTAKE MANIFOLD
NEW 4 BARREL 650 CFM EDELBROCK THUNDER SERIES CARBURETOR W/ ELECTRIC CHOKE
ELECT. PERTRONIX FLAMETHROWER IGNITION DISTRIBUTOR W/ 45,000 VOLT COIL
ACCEL 8MM IGNITION WIRES
NEW THERMOSTAT HOUSING AND THERMOSTAT
NEW HIGH VOLUME CHROME FUEL PUMP
HIGH FLOW WATER PUMP
DIP TUBE AND DIPSTICK
NEW COBRA OVAL BLACK AIR CLEANER WITH PCV VENTILATION SYSTEM
NEW BRAIDED STEEL FUEL LINES AND GAS FILTER
HOT RUN TESTED INCLUDES SETTING INITIAL & FULL TIMING ADVANCE
VIDEO FOOTAGE SHOWN OF YOUR ENGINE IN TEST STAND
Chrome 100 AMP ALTERNATOR- ONE WIRE HOOK UP
Complete MARCH Underdrive POLISHED PULLEY SET
Polished Chrome Alternator Bracket
NEW SERPENTINE BELT INSTALLED AND TENSION ADJUSTED
BALANCED, BLUE PRINTED, ASSEMBLED BY ASE TECHNICIANS
Quicktime Steel Bellhousing
Complete Clutch Kit, Fork, and Starter Installed and Aligned
Tremec TKO 500 5 Speed Transmission
BRAILLE BATTERY B2015 AGM RACING BATTERY LIGHTWEIGHT
Speedway Aluminum Battery Box W/Strap
COMPLETE TOURING FOOTBOX FRESH AIR VENT SYSTEM
WITH AN ADDITIONAL CABLE SET AND HARD SIDE STYLE HOSE
BREEZE AUTOMOTIVE FAN SHROUD
.070 ALUMINUM, 22” x 18” CORE AREA
BREEZE AUTOMOTIVE HEAVY DUTY HINGED RADIATOR/SHROUD MOUNTING KIT
BREEZE AUTOMOTIVE LOWER RADIATOR SUPPORT KIT
SUMITOMO TIRES
Front 245/45X -17 HTR Z
Rear P315/35ZR -17 HTR Z
KUGEL KOMPONENTS CLAMPS
EXTRA FACTORY FIVE RACING ALUMINUM RADIATOR
I'm on page 275 of the build, however I removed the aluminum panels.
So far, I have over $42,000 invested in it. I'm firm at $32,000.
Last edited by Adrianjay; 05-14-2012 at 04:32 AM..
|
Linear Mode
