JRCuz's MK4 Build - FFCars.com : Factory Five Racing Discussion Forum

 28Thanks
Reply
 
LinkBack Thread Tools Display Modes
post #1 of 82 (permalink) Old 03-31-2017, 01:19 PM Thread Starter
Senior Member
 
Join Date: Oct 2013
Location: Stafford, Virginia
Posts: 202
JRCuz's MK4 Build

My complete MK4 kit was delivered 3/23/17. Thanks to Phileas Fogg, CraigS, Dave long time friend and my brother Rick behind the camera. With only a single car garage things are a little tight. We got the body/frame on my dolly and almost immediately snapped one of the wheels off. Thanks to my brother that was repaired and strengthened. The body was removed and put on the body buck without any problem. All but 3 of the 24 boxes were put in my basement. We left IRS center section and spindles plus the front lower control arms in the garage. Inventory went well with only three small items missing. With a call to FFR those items were FEDEXed 3/30. Items on backorder are the overflow tank tubing, quick jack bumper components and my halibrand replica wheels. My wilwood brakes were delivered 3/30.
Now on to the good part, the build. I got the 2 F panels drilled, siliconed and riveted in to place. The front suspension was then installed. One lesson learned is be totally familiar with the method of part installation (don't ask). Now I'll try to post some pics.
JR

Attached Images
File Type: jpg IMG_0200.jpg (270.2 KB, 117 views)
File Type: jpg IMG_0281.jpg (245.6 KB, 112 views)
File Type: jpg IMG_0207.jpg (257.4 KB, 116 views)
File Type: jpg IMG_0220.jpg (256.7 KB, 112 views)
File Type: jpg IMG_0224.jpg (254.8 KB, 122 views)

Mk 4 complete kit ordered 1/19/17, delivered 3/23/17 #9059- 306/TKO 600 from Mike Forte, quicktime bell housing, Forte's hyd clutch, KRC p/s, Kirkey high back seats, 2015 IRS, 17x9/10.5 Halibrand replica wheels, 12.88 wilwood brakes f/r. heater/defroster, dual chrome roll bars
JRCuz is offline  
Sponsored Links
Advertisement
 
post #2 of 82 (permalink) Old 03-31-2017, 01:30 PM Thread Starter
Senior Member
 
Join Date: Oct 2013
Location: Stafford, Virginia
Posts: 202
More pics

Body on body buck and front suspension.
JR

Attached Images
File Type: jpg IMG_0242.jpg (243.6 KB, 110 views)
File Type: jpg IMG_0246.jpg (247.8 KB, 118 views)
File Type: jpg IMG_0252.jpg (247.5 KB, 127 views)
File Type: jpg IMG_0282.jpg (252.9 KB, 131 views)
File Type: jpg IMG_0283.jpg (250.7 KB, 124 views)

Mk 4 complete kit ordered 1/19/17, delivered 3/23/17 #9059- 306/TKO 600 from Mike Forte, quicktime bell housing, Forte's hyd clutch, KRC p/s, Kirkey high back seats, 2015 IRS, 17x9/10.5 Halibrand replica wheels, 12.88 wilwood brakes f/r. heater/defroster, dual chrome roll bars
JRCuz is offline  
post #3 of 82 (permalink) Old 03-31-2017, 04:49 PM
FFCobra Craftsman
 
CraigS's Avatar
 
Join Date: Feb 2005
Location: Manassas, Va
Posts: 17,869
Good going JR! And you got the picture thing figured out too. Nice progress.
JRCuz thanked this.

FFR 5353K, 408W, TKO 500, 2015 IRS w/ 315 gear, Breeze QA1 DA coilovers front and rear, APE hardtop, Forte front swaybar
CraigS is offline  
 
post #4 of 82 (permalink) Old 03-31-2017, 05:28 PM Thread Starter
Senior Member
 
Join Date: Oct 2013
Location: Stafford, Virginia
Posts: 202
Thanks Craig, just a couple of errors on the lower control arms but they were corrected. Thanks to Johns help I got the picture thing figured out.
JR

Mk 4 complete kit ordered 1/19/17, delivered 3/23/17 #9059- 306/TKO 600 from Mike Forte, quicktime bell housing, Forte's hyd clutch, KRC p/s, Kirkey high back seats, 2015 IRS, 17x9/10.5 Halibrand replica wheels, 12.88 wilwood brakes f/r. heater/defroster, dual chrome roll bars
JRCuz is offline  
post #5 of 82 (permalink) Old 03-31-2017, 08:44 PM
Senior Member
 
phileas_fogg's Avatar
 
Join Date: Jul 2014
Location: Fairfax, VA
Posts: 602
Looking good JR! Don't worry about the learning curve; that's part of it. I think there are only two parts on the car that have gone on correctly the first time. Seems like either fit of pilot error always get me. I must have put the lower control arms on and then taken them right back off at least three or four times.

Cheers,


John

P.S. Looks like you've got the picture posting thing licked!
JRCuz thanked this.

MK IV Roadster #8631
Ford 302, Holley Terminator EFI, T5z, 3.55 Rear End, IRS, 17” Halibrand Replicas (9” front, 10.5” rear), Nitto 555 G2’s (275/40ZR17 front, 315/35ZR17 rear), Fast Freddie’s Power Steering, F5 Wilwood Brakes, FFMetal’s Firewall Forward, Forte’s Hydraulic Clutch & Throttle Linkage

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
phileas_fogg is offline  
post #6 of 82 (permalink) Old 03-31-2017, 10:01 PM Thread Starter
Senior Member
 
Join Date: Oct 2013
Location: Stafford, Virginia
Posts: 202
Thanks John, I've just got to get a rhythm going and it'll come together. I'm going to a car show at a high school close to my house. It turns out that there is a guy very close to me with a completed MK3. I just happened to see him on facebook a few days ago. On the pictures any idea why when I click on one of them I get a black box and it acts like it is processing but never displays? I have no problem with this on my tablet.
JR

Mk 4 complete kit ordered 1/19/17, delivered 3/23/17 #9059- 306/TKO 600 from Mike Forte, quicktime bell housing, Forte's hyd clutch, KRC p/s, Kirkey high back seats, 2015 IRS, 17x9/10.5 Halibrand replica wheels, 12.88 wilwood brakes f/r. heater/defroster, dual chrome roll bars
JRCuz is offline  
post #7 of 82 (permalink) Old 04-01-2017, 02:35 PM
Senior Member
 
phileas_fogg's Avatar
 
Join Date: Jul 2014
Location: Fairfax, VA
Posts: 602
Quote:
Originally Posted by JRCuz View Post
On the pictures any idea why when I click on one of them I get a black box and it acts like it is processing but never displays? I have no problem with this on my tablet.
JR
Could be any number of things, but the pictures show up fine for me. If it really bugs you, try a different browser (e.g., if you have the problem with Explorer, download and install Chrome).


John
JRCuz thanked this.

MK IV Roadster #8631
Ford 302, Holley Terminator EFI, T5z, 3.55 Rear End, IRS, 17” Halibrand Replicas (9” front, 10.5” rear), Nitto 555 G2’s (275/40ZR17 front, 315/35ZR17 rear), Fast Freddie’s Power Steering, F5 Wilwood Brakes, FFMetal’s Firewall Forward, Forte’s Hydraulic Clutch & Throttle Linkage

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
phileas_fogg is offline  
post #8 of 82 (permalink) Old 04-01-2017, 03:12 PM
Senior Member
FFCars Craftsman
 
KDubU's Avatar
 
Join Date: Jun 2015
Location: Kennebunk, ME
Posts: 726
Looks like it's coming along nicely. As has been stated you'll likely do things over multiple times and that's part of the experience. Sometimes it can be very frustrating but you'll sure know how to service your roadster going forward.
JRCuz thanked this.

Kyle

MKIV#8707, Picked-up 09/05/15, 351w, TK600, QF680, 15" Halibrands, PS, Wilwoods, Gas-N Headers & Sidepipes, Viking Blue with ith Wimbledon White stripes. First start 03/25/16. First go-cart 04/01/16. Registered and on the road 07/15/16! Painted 03/15/17.
KDubU is offline  
post #9 of 82 (permalink) Old 04-02-2017, 01:27 PM Thread Starter
Senior Member
 
Join Date: Oct 2013
Location: Stafford, Virginia
Posts: 202
Phileas Fogg, you were right John. I switched to google chrome and the pics display fine. Thanks again.
JR

Mk 4 complete kit ordered 1/19/17, delivered 3/23/17 #9059- 306/TKO 600 from Mike Forte, quicktime bell housing, Forte's hyd clutch, KRC p/s, Kirkey high back seats, 2015 IRS, 17x9/10.5 Halibrand replica wheels, 12.88 wilwood brakes f/r. heater/defroster, dual chrome roll bars
JRCuz is offline  
post #10 of 82 (permalink) Old 04-05-2017, 12:23 PM Thread Starter
Senior Member
 
Join Date: Oct 2013
Location: Stafford, Virginia
Posts: 202
Center section

Not a whole lot of progress this week so far. I got the IRS center section painted with POR 15 yesterday in preparation for install hopefully this weekend.
JR

Attached Images
File Type: jpg IMG_0289.jpg (253.4 KB, 77 views)

Mk 4 complete kit ordered 1/19/17, delivered 3/23/17 #9059- 306/TKO 600 from Mike Forte, quicktime bell housing, Forte's hyd clutch, KRC p/s, Kirkey high back seats, 2015 IRS, 17x9/10.5 Halibrand replica wheels, 12.88 wilwood brakes f/r. heater/defroster, dual chrome roll bars
JRCuz is offline  
post #11 of 82 (permalink) Old 04-05-2017, 06:15 PM
FFCobra Craftsman
 
CraigS's Avatar
 
Join Date: Feb 2005
Location: Manassas, Va
Posts: 17,869
If you can get a helper to do the install w/, it will be worthwhile. The problem is that the diff needs to be about 80 degrees nose up to start, and then slowly rotate to horizontal. That 5 inch round pad on my floor jack seemed about 1/4 the size I would have liked during that process.
JRCuz thanked this.

FFR 5353K, 408W, TKO 500, 2015 IRS w/ 315 gear, Breeze QA1 DA coilovers front and rear, APE hardtop, Forte front swaybar
CraigS is offline  
post #12 of 82 (permalink) Old 04-05-2017, 10:09 PM
Senior Member
 
phileas_fogg's Avatar
 
Join Date: Jul 2014
Location: Fairfax, VA
Posts: 602
Failing a helper, use that webbing through the mounting holes or around some bolts through the mounting holes to help keep things steady. Hopefully you'll get lucky like me and it'll go in first time just like it was made to.

If it becomes obvious it won't go in without a helper, give me a shout.


John

MK IV Roadster #8631
Ford 302, Holley Terminator EFI, T5z, 3.55 Rear End, IRS, 17” Halibrand Replicas (9” front, 10.5” rear), Nitto 555 G2’s (275/40ZR17 front, 315/35ZR17 rear), Fast Freddie’s Power Steering, F5 Wilwood Brakes, FFMetal’s Firewall Forward, Forte’s Hydraulic Clutch & Throttle Linkage

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
phileas_fogg is offline  
post #13 of 82 (permalink) Old 04-05-2017, 10:28 PM Thread Starter
Senior Member
 
Join Date: Oct 2013
Location: Stafford, Virginia
Posts: 202
Thanks John, I may give it a try tomorrow. I looked over edwardb's build thread today and I might be able to rig something with my engine hoist. If I'm not successful I'll let you know. I have the diff on my motorcycle lift now I plan to get it in postion and lift it as high as possible with it then use a couple ratchet straps with my hoist to lift it into place. Notice I said plan,
Mike Tyson said everyone has a plan 'til they get punched in the mouth. We'll see how it goes. You may get a call.
JR

Mk 4 complete kit ordered 1/19/17, delivered 3/23/17 #9059- 306/TKO 600 from Mike Forte, quicktime bell housing, Forte's hyd clutch, KRC p/s, Kirkey high back seats, 2015 IRS, 17x9/10.5 Halibrand replica wheels, 12.88 wilwood brakes f/r. heater/defroster, dual chrome roll bars
JRCuz is offline  
post #14 of 82 (permalink) Old 04-06-2017, 01:06 AM
Senior Member
 
carlewms's Avatar
 
Join Date: May 2012
Location: Nokesville
Posts: 561
JR,

Getting that damn pumpkin installed was one of the hardest parts of the build as far as I am concerned.

BTW ... I ended up having to shave a grind a little off the thing (in non vital places) to get it through the tight spot.

I am just up the road in Nokesville BTW so like Craig and John I can help as well.

Carl
JRCuz thanked this.
carlewms is offline  
post #15 of 82 (permalink) Old 04-06-2017, 12:32 PM Thread Starter
Senior Member
 
Join Date: Oct 2013
Location: Stafford, Virginia
Posts: 202
Thanks Carl. I've been following your build for as long as I've been on the forum. I don't know if I will do the bodywork though. I'm going to try the install and see how it goes. You are welcome anytime, I can always use help with the harder(heavier) work. I may be needing help depending how it goes later on today.
Thanks, JR

Mk 4 complete kit ordered 1/19/17, delivered 3/23/17 #9059- 306/TKO 600 from Mike Forte, quicktime bell housing, Forte's hyd clutch, KRC p/s, Kirkey high back seats, 2015 IRS, 17x9/10.5 Halibrand replica wheels, 12.88 wilwood brakes f/r. heater/defroster, dual chrome roll bars
JRCuz is offline  
post #16 of 82 (permalink) Old 04-06-2017, 08:05 PM Thread Starter
Senior Member
 
Join Date: Oct 2013
Location: Stafford, Virginia
Posts: 202
It's in

It took about 3 hrs my engine lift, my motorcycle lift, 3 ratchet straps and a lot of adjusting but I finally got my IRS diff in today. No big deal(Ha Ha). The only problem is I can't get the right rear bolt started. The other 3 bolts were no problem. Here are some pics.
JR
Attached Images
File Type: jpg IMG_0290.jpg (247.8 KB, 71 views)
File Type: jpg IMG_0291.jpg (246.3 KB, 71 views)
File Type: jpg IMG_0292.jpg (244.1 KB, 75 views)
File Type: jpg IMG_0293.jpg (245.0 KB, 66 views)

Mk 4 complete kit ordered 1/19/17, delivered 3/23/17 #9059- 306/TKO 600 from Mike Forte, quicktime bell housing, Forte's hyd clutch, KRC p/s, Kirkey high back seats, 2015 IRS, 17x9/10.5 Halibrand replica wheels, 12.88 wilwood brakes f/r. heater/defroster, dual chrome roll bars
JRCuz is offline  
post #17 of 82 (permalink) Old 04-06-2017, 08:30 PM
Senior Member
 
phileas_fogg's Avatar
 
Join Date: Jul 2014
Location: Fairfax, VA
Posts: 602
There's always one...

Nice work!


John
JRCuz thanked this.

MK IV Roadster #8631
Ford 302, Holley Terminator EFI, T5z, 3.55 Rear End, IRS, 17” Halibrand Replicas (9” front, 10.5” rear), Nitto 555 G2’s (275/40ZR17 front, 315/35ZR17 rear), Fast Freddie’s Power Steering, F5 Wilwood Brakes, FFMetal’s Firewall Forward, Forte’s Hydraulic Clutch & Throttle Linkage

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
phileas_fogg is offline  
post #18 of 82 (permalink) Old 04-06-2017, 08:35 PM
Senior Member
FFCars Master Craftsman
 
BEAR-AvHISTORY's Avatar
 
Join Date: Nov 2013
Location: Raleigh, NC
Posts: 1,968
LOOK'N GOOD!! Don't worry about a few do-overs its all part of the process.
JRCuz thanked this.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


Kevin

Raleigh, NC. MK-IV 8243 Coyote (2011-2014)/TKO-600
Delivered - 2/7/14
Initial Engine Start - 11/12/14
Go Cart - 11/22/14
Chassis to Body Shop - 11/24/14
Body Painted - 1/8/15
Body on Chassis - 1/28/15
Dyno Tune - 2/19/15
Trailer home - 3/7/15
NCDMV inspection - PASSED 3/16/15
Plate - "COYOTE" Black/Yellow NC-1965 - 3/25/15
BEAR-AvHISTORY is offline  
post #19 of 82 (permalink) Old 04-07-2017, 12:12 PM
FFCobra Craftsman
 
CraigS's Avatar
 
Join Date: Feb 2005
Location: Manassas, Va
Posts: 17,869
Yes those rear bolts are a pain. The frame is just a little too wide, or is it too narrow? Seems this is getting to be a common problem as I have seen another thread recently. Here it is w/ a solution.
IRS Center section problem
BTW, you are threading a steel bolt into aluminum so either use NeverSeize or bearing grease on the threads.
JRCuz thanked this.

FFR 5353K, 408W, TKO 500, 2015 IRS w/ 315 gear, Breeze QA1 DA coilovers front and rear, APE hardtop, Forte front swaybar
CraigS is offline  
post #20 of 82 (permalink) Old 04-07-2017, 01:10 PM Thread Starter
Senior Member
 
Join Date: Oct 2013
Location: Stafford, Virginia
Posts: 202
Thanks Craig, I will use anti-seize on the rear bolt threads. I have ny-lok nuts on the front bolts temporarily, do you think they are better than the deformed nuts supplied? I had thought of carving the rear bushings a little. I guess I know what I'm doing today. Thanks again.
JR

Mk 4 complete kit ordered 1/19/17, delivered 3/23/17 #9059- 306/TKO 600 from Mike Forte, quicktime bell housing, Forte's hyd clutch, KRC p/s, Kirkey high back seats, 2015 IRS, 17x9/10.5 Halibrand replica wheels, 12.88 wilwood brakes f/r. heater/defroster, dual chrome roll bars

Last edited by JRCuz; 04-07-2017 at 01:54 PM.
JRCuz is offline  
post #21 of 82 (permalink) Old 04-07-2017, 07:19 PM
FFCobra Craftsman
 
CraigS's Avatar
 
Join Date: Feb 2005
Location: Manassas, Va
Posts: 17,869
I realize that I am a little on the extreme side but I will not use deformed metal nuts anywhere. OTOH, there are 1000s of them doing fine on a lot of FFRs so it's your call.
JRCuz thanked this.

FFR 5353K, 408W, TKO 500, 2015 IRS w/ 315 gear, Breeze QA1 DA coilovers front and rear, APE hardtop, Forte front swaybar
CraigS is offline  
post #22 of 82 (permalink) Old 04-07-2017, 08:18 PM Thread Starter
Senior Member
 
Join Date: Oct 2013
Location: Stafford, Virginia
Posts: 202
Thanks again Craig. I used them on a couple of bolts on the rear upper and lower control arms where I couldn't use the deformed nuts with the flared base.
Thanks, JR

Mk 4 complete kit ordered 1/19/17, delivered 3/23/17 #9059- 306/TKO 600 from Mike Forte, quicktime bell housing, Forte's hyd clutch, KRC p/s, Kirkey high back seats, 2015 IRS, 17x9/10.5 Halibrand replica wheels, 12.88 wilwood brakes f/r. heater/defroster, dual chrome roll bars
JRCuz is offline  
post #23 of 82 (permalink) Old 04-07-2017, 11:25 PM Thread Starter
Senior Member
 
Join Date: Oct 2013
Location: Stafford, Virginia
Posts: 202
More progress today includes diff is installed along with the left and right IRS toe arms, lower control arms and upper control arms. Anti-seize used on the rear diff bolts. All fasteners torqued.
JR
Attached Images
File Type: jpg IMG_0294.jpg (246.4 KB, 57 views)
File Type: jpg IMG_0295.jpg (242.8 KB, 55 views)
File Type: jpg IMG_0296.jpg (243.7 KB, 51 views)
File Type: jpg IMG_0297.jpg (248.9 KB, 54 views)
File Type: jpg IMG_0298.jpg (248.3 KB, 50 views)

Mk 4 complete kit ordered 1/19/17, delivered 3/23/17 #9059- 306/TKO 600 from Mike Forte, quicktime bell housing, Forte's hyd clutch, KRC p/s, Kirkey high back seats, 2015 IRS, 17x9/10.5 Halibrand replica wheels, 12.88 wilwood brakes f/r. heater/defroster, dual chrome roll bars
JRCuz is offline  
post #24 of 82 (permalink) Old 04-08-2017, 01:26 AM
Senior Member
 
carlewms's Avatar
 
Join Date: May 2012
Location: Nokesville
Posts: 561
Nice progress ... no ... great progress. Your cooking with gas now!
JRCuz thanked this.
carlewms is offline  
post #25 of 82 (permalink) Old 04-08-2017, 11:50 PM Thread Starter
Senior Member
 
Join Date: Oct 2013
Location: Stafford, Virginia
Posts: 202
Got the spindles, hubs, coil overs and axles installed and torqued today.
that's about it.
JR
Attached Images
File Type: jpg IMG_0299.jpg (250.7 KB, 51 views)
File Type: jpg IMG_0300.jpg (255.3 KB, 51 views)

Mk 4 complete kit ordered 1/19/17, delivered 3/23/17 #9059- 306/TKO 600 from Mike Forte, quicktime bell housing, Forte's hyd clutch, KRC p/s, Kirkey high back seats, 2015 IRS, 17x9/10.5 Halibrand replica wheels, 12.88 wilwood brakes f/r. heater/defroster, dual chrome roll bars

Last edited by JRCuz; 04-10-2017 at 06:54 PM.
JRCuz is offline  
post #26 of 82 (permalink) Old 04-12-2017, 12:07 AM Thread Starter
Senior Member
 
Join Date: Oct 2013
Location: Stafford, Virginia
Posts: 202
I managed to get a few things done today, including safety wiring the Wilwood hat to rotor bolts and didn't even draw any blood. Also got all 4 calipers and the e-brake calipers installed. The right rear e-brake mechanism was very close to the coilover, I adjusted the IRS a little and it seemed to help. I hope I can get it right when the suspension is aligned. The left front caliper seems to be equally spaced on the rotor but the outside brake pad barely touches the rotor. The large piston in the caliper looks like it is slightly extended and I hope that is the problem. I decided to call it quits for today. I think nearly 9 hrs. straight is enough. Time for a weeks vacation.
JR
Attached Images
File Type: jpg IMG_0301.jpg (252.7 KB, 38 views)
File Type: jpg IMG_0302.jpg (248.0 KB, 37 views)
File Type: jpg IMG_0303.jpg (249.6 KB, 36 views)
File Type: jpg IMG_0304.jpg (245.3 KB, 37 views)
File Type: jpg IMG_0305.jpg (246.1 KB, 37 views)

Mk 4 complete kit ordered 1/19/17, delivered 3/23/17 #9059- 306/TKO 600 from Mike Forte, quicktime bell housing, Forte's hyd clutch, KRC p/s, Kirkey high back seats, 2015 IRS, 17x9/10.5 Halibrand replica wheels, 12.88 wilwood brakes f/r. heater/defroster, dual chrome roll bars

Last edited by JRCuz; 04-12-2017 at 02:41 AM.
JRCuz is offline  
post #27 of 82 (permalink) Old 04-12-2017, 12:10 AM Thread Starter
Senior Member
 
Join Date: Oct 2013
Location: Stafford, Virginia
Posts: 202
Here's a few more.
JR
Attached Images
File Type: jpg IMG_0306.jpg (244.3 KB, 39 views)
File Type: jpg IMG_0307.jpg (248.7 KB, 39 views)
File Type: jpg IMG_0308.jpg (241.7 KB, 35 views)
File Type: jpg IMG_0309.jpg (247.3 KB, 33 views)

Mk 4 complete kit ordered 1/19/17, delivered 3/23/17 #9059- 306/TKO 600 from Mike Forte, quicktime bell housing, Forte's hyd clutch, KRC p/s, Kirkey high back seats, 2015 IRS, 17x9/10.5 Halibrand replica wheels, 12.88 wilwood brakes f/r. heater/defroster, dual chrome roll bars
JRCuz is offline  
post #28 of 82 (permalink) Old 04-25-2017, 01:07 PM Thread Starter
Senior Member
 
Join Date: Oct 2013
Location: Stafford, Virginia
Posts: 202
E-Brake Cables

I'm using the 12.88 Wilwood Brakes on my MK4 with 2015 Mustang IRS. No e-brake cables came with my complete kit. Has anyone with this setup used the Wilwood e-brake cables p/n 330-9371?
Thanks JR

Mk 4 complete kit ordered 1/19/17, delivered 3/23/17 #9059- 306/TKO 600 from Mike Forte, quicktime bell housing, Forte's hyd clutch, KRC p/s, Kirkey high back seats, 2015 IRS, 17x9/10.5 Halibrand replica wheels, 12.88 wilwood brakes f/r. heater/defroster, dual chrome roll bars
JRCuz is offline  
post #29 of 82 (permalink) Old 04-25-2017, 01:16 PM
Senior Member
 
phileas_fogg's Avatar
 
Join Date: Jul 2014
Location: Fairfax, VA
Posts: 602
Hmmm. I received emergency brake cables in Box 11 with my [old style] IRS components. Seems odd F5 doesn't provide cables with the new IRS. Forgive the question, but are the cables listed on the inventory?


John

MK IV Roadster #8631
Ford 302, Holley Terminator EFI, T5z, 3.55 Rear End, IRS, 17” Halibrand Replicas (9” front, 10.5” rear), Nitto 555 G2’s (275/40ZR17 front, 315/35ZR17 rear), Fast Freddie’s Power Steering, F5 Wilwood Brakes, FFMetal’s Firewall Forward, Forte’s Hydraulic Clutch & Throttle Linkage

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
phileas_fogg is offline  
post #30 of 82 (permalink) Old 04-25-2017, 02:46 PM Thread Starter
Senior Member
 
Join Date: Oct 2013
Location: Stafford, Virginia
Posts: 202
Hi John, no problem. I've looked through the inventory sheets several times and not seen the e-brake cables listed. Next step I'll look through the boxes.
JR

Mk 4 complete kit ordered 1/19/17, delivered 3/23/17 #9059- 306/TKO 600 from Mike Forte, quicktime bell housing, Forte's hyd clutch, KRC p/s, Kirkey high back seats, 2015 IRS, 17x9/10.5 Halibrand replica wheels, 12.88 wilwood brakes f/r. heater/defroster, dual chrome roll bars
JRCuz is offline  
Sponsored Links
Advertisement
 
Reply

Bookmarks

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the FFCars.com : Factory Five Racing Discussion Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.




Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome

 

Welcome to FFCars! The representations expressed are the representations and opinions of the FFCars.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Factory Five Racing, Inc. or Ford Motor Company. This website has been planned and developed by FFCars.com and its forum members and should not be construed as being endorsed by Factory Five Racing, Inc. or Ford Motor Company for any purpose. "FFR", "Factory Five", "Factory Five Racing", and the Factory Five Racing logo are registered trademarks of Factory Five Racing, Inc. FFCars.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting the FFCars.com Forum dedicated to Factory Five.